WEKO3
インデックスリンク
アイテム
旋削加工における工具-切りくず接触面温度の測定
http://hdl.handle.net/2297/37003
http://hdl.handle.net/2297/370031cde17ae-f068-44af-8493-ea4101a64592
| 名前 / ファイル | ライセンス | アクション |
|---|---|---|
TE-PR-UEDA-T-2094.pdf (675.0 kB)
|
|
| Item type | 学術雑誌論文 / Journal Article(1) | |||||
|---|---|---|---|---|---|---|
| 公開日 | 2017-10-03 | |||||
| タイトル | ||||||
| タイトル | 旋削加工における工具-切りくず接触面温度の測定 | |||||
| タイトル | ||||||
| タイトル | Measurement of Tool-Chip Interfaee Temperature in Turning Using Two-Color Pyrometer | |||||
| 言語 | en | |||||
| 言語 | ||||||
| 言語 | jpn | |||||
| 資源タイプ | ||||||
| 資源タイプ識別子 | http://purl.org/coar/resource_type/c_6501 | |||||
| 資源タイプ | journal article | |||||
| 著者 |
Al Huda, Mahfudz
× Al Huda, Mahfudz× 山田, 啓司× 上田, 隆司 |
|||||
| 書誌情報 |
日本機械学會論文集 C編 = Transactions of the Japan Society of Mechanical Engineers Series C 巻 65, 号 633, p. 2094-2101, 発行日 1999-05-25 |
|||||
| ISSN | ||||||
| 収録物識別子タイプ | ISSN | |||||
| 収録物識別子 | 0387-5024 | |||||
| NCID | ||||||
| 収録物識別子タイプ | NCID | |||||
| 収録物識別子 | AN00187463 | |||||
| DOI | ||||||
| 関連タイプ | isIdenticalTo | |||||
| 識別子タイプ | DOI | |||||
| 関連識別子 | 10.1299/kikaic.65.2094 | |||||
| 出版者 | ||||||
| 出版者 | The Japan Society of Mechanical Engineers = 日本機械学会 | |||||
| 抄録 | ||||||
| 内容記述タイプ | Abstract | |||||
| 内容記述 | The temperature of interface between a cutting tool and a chip in dry and wet turning is measured using two color pyrometer with a fused fiber coupler. A translucent Alumina sintered under HIP (Hot Isostatic Pressing) is used as the cutting tool, and 0.45% carbon steel (S45C) is used as a workpiece. The water soluble fluid (Sunlight TC-800) is used as the cutting fluid, and is introduced onto the rake surface of the tool with a nozzle (diameter: 5 mm). The infrared rays radiated and transmitted through the translucent tool are accepted by an optical fiber, and separated to two optical fibers at fused fiber coupler. Each fiber leads the infrared ray, respectively, to two infrared detectors of different spectral sensitivity. Temperature is obtained by calculating the ratio of the output voltage from these two detectorS. The result obtained are as follows: (1) The technique developed is suitable for measuring the interface temperature between a cutting tool and a chip. (2) The interface temperature is highly affected by the cutting speed, and the temperature increases very rapidly with the increase of cutting speed. (3) The interface temperature reduced 30°C in the wet cutting. Finally, the temperature distributions on the cutting tool and the work material are analyzed by using a finite element method (FEM). Good agreement is obtained between the analytical results and the experimental ones. | |||||
| 権利 | ||||||
| 権利情報 | Copyright © The Japan Society of Mechanical Engineers 日本機械学会 | |||||
| 著者版フラグ | ||||||
| 出版タイプ | VoR | |||||
| 出版タイプResource | http://purl.org/coar/version/c_970fb48d4fbd8a85 | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | https://www.jstage.jst.go.jp/browse/kikaic1979/-char/ja/ | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | http://www.jsme.or.jp/ | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | http://ci.nii.ac.jp/naid/110002384190 | |||||
