WEKO3
インデックスリンク
アイテム
CBN工具による高硬度鋼の旋削温度測定
http://hdl.handle.net/2297/39333
http://hdl.handle.net/2297/39333d241a76f-1d62-46e3-aa80-3c7084ed46de
| 名前 / ファイル | ライセンス | アクション |
|---|---|---|
TE-PR-UEDA-T-1684.pdf (1.0 MB)
|
|
| Item type | 学術雑誌論文 / Journal Article(1) | |||||
|---|---|---|---|---|---|---|
| 公開日 | 2017-10-03 | |||||
| タイトル | ||||||
| タイトル | CBN工具による高硬度鋼の旋削温度測定 | |||||
| タイトル | ||||||
| タイトル | Measurement of Temperature of CBN Tool in Turning of High Hardness Steel | |||||
| 言語 | en | |||||
| 言語 | ||||||
| 言語 | jpn | |||||
| 資源タイプ | ||||||
| 資源タイプ識別子 | http://purl.org/coar/resource_type/c_6501 | |||||
| 資源タイプ | journal article | |||||
| 著者 |
Al Huda, Mahfudz
× Al Huda, Mahfudz× 山田, 啓司× 上田, 隆司 |
|||||
| 書誌情報 |
精密工学会誌 = Journal of the Japan Society of Precision Engineering 巻 64, 号 11, p. 1684-1688, 発行日 1998-11-05 |
|||||
| ISSN | ||||||
| 収録物識別子タイプ | ISSN | |||||
| 収録物識別子 | 0912-0289 | |||||
| NCID | ||||||
| 収録物識別子タイプ | NCID | |||||
| 収録物識別子 | AN1003250X | |||||
| DOI | ||||||
| 関連タイプ | isIdenticalTo | |||||
| 識別子タイプ | DOI | |||||
| 関連識別子 | 10.2493/jjspe.64.1684 | |||||
| 出版者 | ||||||
| 出版者 | 精密工学会 = The Japan Society for Precision Engineering | |||||
| 抄録 | ||||||
| 内容記述タイプ | Abstract | |||||
| 内容記述 | The temperature of the flank side of the cutting tool edge that has large affect on machined surface integrity is measured using two-color pyrometer with a fused fiber coupler. The infrared rays radiated from the cutting tool edge are accepted by an optical fiber, and separated to two optical fibers at the fused fiber coupler. Each fiber leads the infrared ray, respectively, to two infrared detectors with different characteristic of spectral sensitivity. Temperature is obtained by calculating the ratio of the output voltage from these two detectors. A CBN tool (CBN content : 60 volume percent, density : 3000 kg/mm2) is used as the cutting tool. Annealed steel (S45C), bearing steel (SUJ2), and quenched steel (S55C) are used as the cutting materials to investigate their affect on the tool edge temperature. The results obtained are as follows : (1) The technique developed is suitable for measuring the temperature of the flank side of the cutting tool edge. (2) The temperature of the cutting tool edge is highly effected by cutting speed. (3) The temperature increases slightly with the increase of depth of cut and feed rate. (4) On the cutting of quenched steel which has the largest hardness among these three materials, the temperature is about 50°C higher than that on the bearing steel cutting, and the temperature of the annealed steel cutting is the lowest. | |||||
| 権利 | ||||||
| 権利情報 | Copyright © 2007 The Japan Society for Precision Engineering 精密工学会 | |||||
| 著者版フラグ | ||||||
| 出版タイプ | VoR | |||||
| 出版タイプResource | http://purl.org/coar/version/c_970fb48d4fbd8a85 | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | http://www.jspe.or.jp/ | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | https://www.jstage.jst.go.jp/browse/jjspe | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | http://ci.nii.ac.jp/naid/110001372326 | |||||
