WEKO3
インデックスリンク
アイテム
断続切削における工具逃げ面温度: 高速エンドミル加工に関する研究(第1報)
http://hdl.handle.net/2297/38803
http://hdl.handle.net/2297/388038dead67a-b9fc-45d8-b2a5-4847185ee106
| 名前 / ファイル | ライセンス | アクション |
|---|---|---|
TE-PR-HOSOKAWA-A-1786.pdf (2.7 MB)
|
|
| Item type | 学術雑誌論文 / Journal Article(1) | |||||
|---|---|---|---|---|---|---|
| 公開日 | 2017-10-03 | |||||
| タイトル | ||||||
| タイトル | 断続切削における工具逃げ面温度: 高速エンドミル加工に関する研究(第1報) | |||||
| タイトル | ||||||
| タイトル | Temperature of Tool Flank in Intermittent Cutting: Studies on High Speed Endmilling(1st Report) | |||||
| 言語 | en | |||||
| 言語 | ||||||
| 言語 | jpn | |||||
| 資源タイプ | ||||||
| 資源タイプ識別子 | http://purl.org/coar/resource_type/c_6501 | |||||
| 資源タイプ | journal article | |||||
| 著者 |
細川, 晃
× 細川, 晃× 小田, 健作× 山田, 啓司× 上田, 隆司 |
|||||
| 書誌情報 |
精密工学会誌 = Journal of the Japan Society of Precision Engineering 巻 66, 号 11, p. 1786-1791, 発行日 2000-01-01 |
|||||
| ISSN | ||||||
| 収録物識別子タイプ | ISSN | |||||
| 収録物識別子 | 0912-0289 | |||||
| NCID | ||||||
| 収録物識別子タイプ | NCID | |||||
| 収録物識別子 | AN1003250X | |||||
| DOI | ||||||
| 関連タイプ | isIdenticalTo | |||||
| 識別子タイプ | DOI | |||||
| 関連識別子 | 10.2493/jjspe.66.1786 | |||||
| 出版者 | ||||||
| 出版者 | 精密工学会 = The Japan Society for Precision Engineering | |||||
| 抄録 | ||||||
| 内容記述タイプ | Abstract | |||||
| 内容記述 | The temperature of cutting tool in high speed endmilling is measured using a two-color pyrometer with an optical fiber. This pyrometer has a flat response for the square-wave signal up to approximately 400kHz, which is enough speed to measure the temperature of an endmilling cutter passing at a cutting speed of 628m/min. The influence of cutting speed v and feed per tooth f on the cutting temperature at the flank face of the cemented carbide insert is investigated. The heating and cooling characteristics of the cutting tool during an intermittent cutting cycle are also examined. In dry cutting of carbon steel, the cutting tool temperature θα rises rapidly with the increase of cutting speed and θα reaches approximately 770°C at v=628m/min. The feed per tooth, however, has less effect on cutting tool temperature. The temperature change during an intermittent cutting process is about 150°C when v=471.2m/min and f=0.047mm/tooth. The temperature distribution along the contact edge between a tool and workpiece is almost uniform although those at tool tip and boundary region are somewhat higher. | |||||
| 権利 | ||||||
| 権利情報 | Copyright © 2007 The Japan Society for Precision Engineering 精密工学会 | |||||
| 著者版フラグ | ||||||
| 出版タイプ | VoR | |||||
| 出版タイプResource | http://purl.org/coar/version/c_970fb48d4fbd8a85 | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | http://www.jspe.or.jp/ | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | https://www.jstage.jst.go.jp/browse/jjspe | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | http://ci.nii.ac.jp/naid/110001372822/ | |||||
