WEKO3
インデックスリンク
アイテム
反応・溶媒除去を伴うポリイミドフィルムのテンター内加熱時のボーイング現象の予測
http://hdl.handle.net/2297/36570
http://hdl.handle.net/2297/3657089b94687-72c4-459a-85d2-1bf190edce8d
| 名前 / ファイル | ライセンス | アクション |
|---|---|---|
TE-PR-YAMADA-T-883.pdf (2.0 MB)
|
|
| Item type | 学術雑誌論文 / Journal Article(1) | |||||
|---|---|---|---|---|---|---|
| 公開日 | 2017-10-03 | |||||
| タイトル | ||||||
| タイトル | 反応・溶媒除去を伴うポリイミドフィルムのテンター内加熱時のボーイング現象の予測 | |||||
| タイトル | ||||||
| タイトル | Prediction of Bowing Phenomenon for Polyimide Film Accompanying Reactions and Removal of Solvents During Film Heating with Tenter | |||||
| 言語 | en | |||||
| 言語 | ||||||
| 言語 | jpn | |||||
| 資源タイプ | ||||||
| 資源タイプ識別子 | http://purl.org/coar/resource_type/c_6501 | |||||
| 資源タイプ | journal article | |||||
| 著者 |
伊藤, 利尚
× 伊藤, 利尚× 山田, 敏郎× 杉原, 元樹× 森, 計吾 |
|||||
| 書誌情報 |
成形加工 = Journal of the Japan Society of Polymer Processing 巻 18, 号 12, p. 883-889, 発行日 2006-12-20 |
|||||
| ISSN | ||||||
| 収録物識別子タイプ | ISSN | |||||
| 収録物識別子 | 0915-4027 | |||||
| NCID | ||||||
| 収録物識別子タイプ | NCID | |||||
| 収録物識別子 | AN10278882 | |||||
| DOI | ||||||
| 関連タイプ | isIdenticalTo | |||||
| 識別子タイプ | DOI | |||||
| 関連識別子 | 10.4325/seikeikakou.18.883 | |||||
| 出版者 | ||||||
| 出版者 | The Japan Society of Polymer Processing = プラスチック成形加工学会 | |||||
| 抄録 | ||||||
| 内容記述タイプ | Abstract | |||||
| 内容記述 | n this report, the bowing behavior and the state of stress in PI film during tenter heating process were predicted by a finite element method (FEM). In the FEM analysis, the authors focused especially on the first zone of tenter heating where the shrinking stress and changes in film hardness arise resulting from removal of residual solvents and chemical reaction (imidation). The analysis was carried out under the assumption that the PI film in the tenter heating was linear-elastic. From the orientation measurements of PI film, which underwent the heating at the tenter 1st zone, the angle of orientation axis at the film edges tilted approximately 45 degrees from the machine direction (MD) and became level with the transverse direction (TD) at film center. These results comparatively agreed with the direction of the maximum principal stress calculated by FEM. Moreover the FEM results revealed reverse bowing around the entrance of tenter. | |||||
| 権利 | ||||||
| 権利情報 | Copyright © The Japan Society of Polymer Processing プラスチック成形加工学会 | |||||
| 著者版フラグ | ||||||
| 出版タイプ | VoR | |||||
| 出版タイプResource | http://purl.org/coar/version/c_970fb48d4fbd8a85 | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | https://www.jstage.jst.go.jp/browse/seikeikakou/-char/ja/ | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | http://ci.nii.ac.jp/naid/10018695490/ | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | http://www.jspp.or.jp/ | |||||
