WEKO3
アイテム
二軸延伸PETフィルムの横延伸工程における厚み挙動
http://hdl.handle.net/2297/36567
http://hdl.handle.net/2297/36567d0421696-a73d-4211-b232-e9b75b4f7671
| 名前 / ファイル | ライセンス | アクション |
|---|---|---|
TE-PR-YAMADA-T-636.pdf (4.1 MB)
|
|
| Item type | 学術雑誌論文 / Journal Article(1) | |||||
|---|---|---|---|---|---|---|
| 公開日 | 2017-10-03 | |||||
| タイトル | ||||||
| タイトル | 二軸延伸PETフィルムの横延伸工程における厚み挙動 | |||||
| タイトル | ||||||
| タイトル | Thickness Behavior of Biaxially Stretched PET Film in the Transverse Stretching Zone of a Tenter | |||||
| 言語 | en | |||||
| 言語 | ||||||
| 言語 | jpn | |||||
| 資源タイプ | ||||||
| 資源タイプ識別子 | http://purl.org/coar/resource_type/c_6501 | |||||
| 資源タイプ | journal article | |||||
| 著者 |
山田, 敏郎
× 山田, 敏郎× 那須, 礼学× 岩崎, 貴之× 杉原, 元樹 |
|||||
| 書誌情報 |
成形加工 = Journal of the Japan Society of Polymer Processing 巻 17, 号 9, p. 636-641, 発行日 2005-09-20 |
|||||
| ISSN | ||||||
| 収録物識別子タイプ | ISSN | |||||
| 収録物識別子 | 0915-4027 | |||||
| NCID | ||||||
| 収録物識別子タイプ | NCID | |||||
| 収録物識別子 | AN10278882 | |||||
| DOI | ||||||
| 関連タイプ | isIdenticalTo | |||||
| 識別子タイプ | DOI | |||||
| 関連識別子 | 10.4325/seikeikakou.17.636 | |||||
| 出版者 | ||||||
| 出版者 | The Japan Society of Polymer Processing = プラスチック成形加工学会 | |||||
| 抄録 | ||||||
| 内容記述タイプ | Abstract | |||||
| 内容記述 | An uneven thickness distribution can cause serious problems in practical applications. In this report the deformation and thickness behavior of poly (ethylene terephthalate) (PET) film during transverse stretching in a tenter is discussed. The experiments were performed in a pilot plant with extrusion, casting, machine direction (MD) stretching, transverse direction (TD) stretching and thermosetting and winding processes. The thickness distribution of the PET film was measured after uniaxial orientation (MD stretched) and again after biaxial orientation (TD stretched in the tenter). The thickness behavior during the transverse stretching in the tenter was calculated by a finite element method (FEM), assuming a rigid-plastic or elastic-plastic constitutive law with parameters determined from the tensile stress-strain measurements. The tensile stress-strain tests were performed on MD stretched film in the transverse stretching direction. The FEM analysis was carried out using the measured initial thickness distribution of the uniaxially oriented film (MD stretched). It was estimated from this analysis that the (TD) stretching of the film in the tenter initiated near the tenter clip (edge of film), spread to the center of the film and then finally moved from the center to the edge of the film under the experimental conditions of this study. Good agreement was obtained between the experimental and predicted FEM results for the final film thickness distribution after transverse stretching. | |||||
| 権利 | ||||||
| 権利情報 | Copyright © The Japan Society of Polymer Processing プラスチック成形加工学会 | |||||
| 著者版フラグ | ||||||
| 出版タイプ | VoR | |||||
| 出版タイプResource | http://purl.org/coar/version/c_970fb48d4fbd8a85 | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | https://www.jstage.jst.go.jp/browse/seikeikakou/-char/ja/ | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | http://ci.nii.ac.jp/naid/10016932504/ | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | http://www.jspp.or.jp/ | |||||
