WEKO3
インデックスリンク
アイテム
CO2レーザによる鋼の表面改質層の被削性とその改善
http://hdl.handle.net/2297/37004
http://hdl.handle.net/2297/37004a97fc569-08f1-4739-a0c0-19b5945bca48
| 名前 / ファイル | ライセンス | アクション |
|---|---|---|
TE-PR-UEDA-T-879.pdf (854.1 kB)
|
|
| Item type | 学術雑誌論文 / Journal Article(1) | |||||
|---|---|---|---|---|---|---|
| 公開日 | 2017-10-03 | |||||
| タイトル | ||||||
| タイトル | CO2レーザによる鋼の表面改質層の被削性とその改善 | |||||
| タイトル | ||||||
| タイトル | Machinability of Steels After Heat Treatment with CO2 Laser and Its Improvement | |||||
| 言語 | en | |||||
| 言語 | ||||||
| 言語 | jpn | |||||
| 資源タイプ | ||||||
| 資源タイプ識別子 | http://purl.org/coar/resource_type/c_6501 | |||||
| 資源タイプ | journal article | |||||
| 著者 |
田中, 隆太郎
× 田中, 隆太郎× 上田, 隆司× 細川, 晃× 林, 勇伝× 山田, 啓司 |
|||||
| 書誌情報 |
日本機械学會論文集 C編 = Transactions of the Japan Society of Mechanical Engineers Series C 巻 73, 号 727, p. 879-884, 発行日 2007-03-25 |
|||||
| ISSN | ||||||
| 収録物識別子タイプ | ISSN | |||||
| 収録物識別子 | 0387-5024 | |||||
| NCID | ||||||
| 収録物識別子タイプ | NCID | |||||
| 収録物識別子 | AN00187463 | |||||
| DOI | ||||||
| 関連タイプ | isIdenticalTo | |||||
| 識別子タイプ | DOI | |||||
| 関連識別子 | 10.1299/kikaic.73.879 | |||||
| 出版者 | ||||||
| 出版者 | The Japan Society of Mechanical Engineers = 日本機械学会 | |||||
| 抄録 | ||||||
| 内容記述タイプ | Abstract | |||||
| 内容記述 | This study deals with the machinability of steels after heat treatment with CO2, laser using h-BN powder and blast furnace slug as absorbent. h-BN is well known as solid lubricant. As for blast furnace slug, its composition is similar to that of inclusions in calcium dioxide steel that shows good machinability. The absorbance of slug and h-BN were more than 80%, so it is said that these powders can be used as absorbent for CO2, laser. Only in the case of h-BN, absorbent was melted into substrate and its depth was about 200 μm. When turning the steels after laser heat treatment using h-BN power and blast furnace slug as absorbent, carbide tool showed smaller tool wear than the case of carbon type absorbent. In the profile of the machined surface, there was a wave of about 5 μm in amplitude and its wavelength was equal to the feed rate of laser in heat treatment. This is because the workpiece surface after laser heat treatment has a periodic distribution in hardness. The hardness in the surface layer of workpiece was higher than that of the substrate. | |||||
| 権利 | ||||||
| 権利情報 | Copyright © The Japan Society of Mechanical Engineers 日本機械学会 | |||||
| 著者版フラグ | ||||||
| 出版タイプ | VoR | |||||
| 出版タイプResource | http://purl.org/coar/version/c_970fb48d4fbd8a85 | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | https://www.jstage.jst.go.jp/browse/kikaic1979/-char/ja/ | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | http://www.jsme.or.jp/ | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | http://ci.nii.ac.jp/naid/110006271412 | |||||
