WEKO3
インデックスリンク
アイテム
レーザ熱処理による切りくず処理性の改善に関する基礎的研究
http://hdl.handle.net/2297/38916
http://hdl.handle.net/2297/38916f68fc5d0-5f85-4655-8e01-41f57bfdd031
| 名前 / ファイル | ライセンス | アクション |
|---|---|---|
TE-PR-UEDA-T-1025.pdf (1.5 MB)
|
|
| Item type | 学術雑誌論文 / Journal Article(1) | |||||
|---|---|---|---|---|---|---|
| 公開日 | 2017-10-03 | |||||
| タイトル | ||||||
| タイトル | レーザ熱処理による切りくず処理性の改善に関する基礎的研究 | |||||
| タイトル | ||||||
| タイトル | Fundamental Study on Improvement of Chip Controllability in Turning with Laser Heat Treatment | |||||
| 言語 | en | |||||
| 言語 | ||||||
| 言語 | jpn | |||||
| 資源タイプ | ||||||
| 資源タイプ識別子 | http://purl.org/coar/resource_type/c_6501 | |||||
| 資源タイプ | journal article | |||||
| 著者 |
田中, 隆太郎
× 田中, 隆太郎× 林, 勇伝× 田邉, 一真× 上田, 隆司× 細川, 晃 |
|||||
| 書誌情報 |
精密工学会誌 = Journal of the Japan Society of Precision Engineering 巻 73, 号 9, p. 1025-1029, 発行日 2007-09-05 |
|||||
| ISSN | ||||||
| 収録物識別子タイプ | ISSN | |||||
| 収録物識別子 | 0912-0289 | |||||
| NCID | ||||||
| 収録物識別子タイプ | NCID | |||||
| 収録物識別子 | AN1003250X | |||||
| DOI | ||||||
| 関連タイプ | isIdenticalTo | |||||
| 識別子タイプ | DOI | |||||
| 関連識別子 | 10.2493/jjspe.73.1025 | |||||
| 出版者 | ||||||
| 出版者 | 精密工学会 = The Japan Society for Precision Engineering | |||||
| 抄録 | ||||||
| 内容記述タイプ | Abstract | |||||
| 内容記述 | This study deals with the trial for improvement of chip controllability in turning with selective laser heat treatment for workpiece. Selective heat treatment for carbon steel JIS S45C was carried out with Nd:YAG laser which could be transmitted through an optical fiber and shows higher absorption rate against carbon steels than CO2 laser. In turning of these selective laser heat threatened carbon steel, the chip form changed regular curl from irregular curl and chip breakability was improved compared with non-laser treated carbon steel. Surface roughness was obviously smaller comparing with non-laser treated carbon steel. Especially in the case that the depth of cut was larger, the surface roughness was smaller. As for cutting force, the principal force was slightly smaller, but the thrust force and feed force were almost the same. The cutting temperature was slightly lower. The tool wear was almost same as that in the case of non-laser treated carbon steel. | |||||
| 権利 | ||||||
| 権利情報 | Copyright © 2007 The Japan Society for Precision Engineering 精密工学会 | |||||
| 著者版フラグ | ||||||
| 出版タイプ | VoR | |||||
| 出版タイプResource | http://purl.org/coar/version/c_970fb48d4fbd8a85 | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | http://www.jspe.or.jp/ | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | https://www.jstage.jst.go.jp/browse/jjspe | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | http://ci.nii.ac.jp/naid/110006420367 | |||||
