WEKO3
インデックスリンク
アイテム
超仕上加工における切削性能のファジィ制御
http://hdl.handle.net/2297/38797
http://hdl.handle.net/2297/38797e96c53a1-2d70-40e2-8bd3-7f6e654ee669
| 名前 / ファイル | ライセンス | アクション |
|---|---|---|
TE-PR-UEDA-T-287.pdf (1.0 MB)
|
|
| Item type | 学術雑誌論文 / Journal Article(1) | |||||
|---|---|---|---|---|---|---|
| 公開日 | 2017-10-03 | |||||
| タイトル | ||||||
| タイトル | 超仕上加工における切削性能のファジィ制御 | |||||
| タイトル | ||||||
| タイトル | Fuzzy Control of Cutting Ability in Superfinishing | |||||
| 言語 | en | |||||
| 言語 | ||||||
| 言語 | jpn | |||||
| 資源タイプ | ||||||
| 資源タイプ識別子 | http://purl.org/coar/resource_type/c_6501 | |||||
| 資源タイプ | journal article | |||||
| 著者 |
坂本, 智
× 坂本, 智× 上田, 隆司 |
|||||
| 書誌情報 |
精密工学会誌 = Journal of the Japan Society of Precision Engineering 巻 64, 号 2, p. 287-291, 発行日 1998-01-01 |
|||||
| ISSN | ||||||
| 収録物識別子タイプ | ISSN | |||||
| 収録物識別子 | 0912-0289 | |||||
| NCID | ||||||
| 収録物識別子タイプ | NCID | |||||
| 収録物識別子 | AN1003250X | |||||
| DOI | ||||||
| 関連タイプ | isIdenticalTo | |||||
| 識別子タイプ | DOI | |||||
| 関連識別子 | 10.2493/jjspe.64.287 | |||||
| 出版者 | ||||||
| 出版者 | 精密工学会 = The Japan Society for Precision Engineering | |||||
| 抄録 | ||||||
| 内容記述タイプ | Abstract | |||||
| 内容記述 | Fuzzy control is applied to the superfinishing in order to optimize the cutting ability of the stone. The finishing performance of vitrified bonded WA stone is regarded as the fuzzy goal. At the beginning of cutting, the stone is in the stage of cutting to get high stock removal rate. But the cutting ability is decreasing as the finishing proceeds and is lost at the end of finishing, resulting in getting the smooth surface. A cutting resistance is used to monitor the cutting condition of stone. The cutting ability of stone is controlled by both the stone pressure and the amount of electricity for electrolytic in-process dressing. A water-solution type coolant and metal bonded diamond stone are used. The main results obtained are as follows. Fuzzy control makes it possible to give the optimized cutting ability to the diamond stone. In the first case, it is possible to get the large stock removal following the smooth surface in a limited time. In second case, it is possible to minimize the finishing time in which the finishing performance intended in stock removal and surface roughness is obtained. In third case, it is possible to keep the cutting ability of stone constant for a long time. | |||||
| 権利 | ||||||
| 権利情報 | Copyright © 2007 The Japan Society for Precision Engineering 精密工学会 | |||||
| 著者版フラグ | ||||||
| 出版タイプ | VoR | |||||
| 出版タイプResource | http://purl.org/coar/version/c_970fb48d4fbd8a85 | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | http://www.jspe.or.jp/ | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | https://www.jstage.jst.go.jp/browse/jjspe | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | http://ci.nii.ac.jp/naid/110001372378/ | |||||
