WEKO3
インデックスリンク
アイテム
白金合金Pt850の切削における工具摩耗特性
http://hdl.handle.net/2297/38766
http://hdl.handle.net/2297/387664c27049b-cd74-470b-afd5-5f1fcc11a604
| 名前 / ファイル | ライセンス | アクション |
|---|---|---|
TE-PR-UEDA-T-839.pdf (5.8 MB)
|
|
| Item type | 学術雑誌論文 / Journal Article(1) | |||||
|---|---|---|---|---|---|---|
| 公開日 | 2017-10-03 | |||||
| タイトル | ||||||
| タイトル | 白金合金Pt850の切削における工具摩耗特性 | |||||
| タイトル | ||||||
| タイトル | Tool Wear Characteristics in Turning of Platinum Alloy Pt850 | |||||
| 言語 | en | |||||
| 言語 | ||||||
| 言語 | jpn | |||||
| 資源タイプ | ||||||
| 資源タイプ識別子 | http://purl.org/coar/resource_type/c_6501 | |||||
| 資源タイプ | journal article | |||||
| 著者 |
佐藤, 昌彦
× 佐藤, 昌彦× 上田, 隆司 |
|||||
| 書誌情報 |
精密工学会誌 = Journal of the Japan Society of Precision Engineering 巻 67, 号 5, p. 839-843, 発行日 2001-01-01 |
|||||
| ISSN | ||||||
| 収録物識別子タイプ | ISSN | |||||
| 収録物識別子 | 0912-0289 | |||||
| NCID | ||||||
| 収録物識別子タイプ | NCID | |||||
| 収録物識別子 | AN1003250X | |||||
| DOI | ||||||
| 関連タイプ | isIdenticalTo | |||||
| 識別子タイプ | DOI | |||||
| 関連識別子 | 10.2493/jjspe.67.839 | |||||
| 出版者 | ||||||
| 出版者 | 精密工学会 = The Japan Society for Precision Engineering | |||||
| 抄録 | ||||||
| 内容記述タイプ | Abstract | |||||
| 内容記述 | In turning of platinum alloy Pt850, the wear behavior of tools and the cutting characteristics of Pt850 are investigated experimentally. K10 carbide, cermet, ceramics and PCD are used as tool materials. K10 carbide and cermet are not suitable for the cutting of this material because severe wear on the tool flank was observed after a few second of cutting, that is, the width of the flank wear land was about 1 mm after 10 seconds cutting. The width of wear land of Al2O3 and Si3N4 ceramic tools was small compared with K10 carbide tool, but the cutting forces increased rapidly as the cutting proceed. PCD tool can be used for cutting of Pt850 because the width of flank wear land is much small compared with other tool materials used in this experiment and the increasing rate of cutting force is not so great. The influence of cutting speed on the flank wear of PCD tool is small. The surface roughness of work material Pt850 becomes lower when the smaller feed rate is chosen as a cutting condition and the cutting tool of larger radius corner is used. | |||||
| 権利 | ||||||
| 権利情報 | Copyright © 2007 The Japan Society for Precision Engineering 精密工学会 | |||||
| 著者版フラグ | ||||||
| 出版タイプ | VoR | |||||
| 出版タイプResource | http://purl.org/coar/version/c_970fb48d4fbd8a85 | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | http://www.jspe.or.jp/ | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | https://www.jstage.jst.go.jp/browse/jjspe | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | http://ci.nii.ac.jp/naid/110001368226/ | |||||
