WEKO3
インデックスリンク
アイテム
ファインセラミックスの湿式研削における熱流入割合: 硬ぜい材料の研削加工に関する研究(第2報)
http://hdl.handle.net/2297/43483
http://hdl.handle.net/2297/434835496adaf-6f7e-439a-85b3-af45cd47a632
| 名前 / ファイル | ライセンス | アクション |
|---|---|---|
TE-PR-HOSOKAWA-A-883.pdf (4.4 MB)
|
|
| Item type | 学術雑誌論文 / Journal Article(1) | |||||
|---|---|---|---|---|---|---|
| 公開日 | 2017-10-03 | |||||
| タイトル | ||||||
| タイトル | ファインセラミックスの湿式研削における熱流入割合: 硬ぜい材料の研削加工に関する研究(第2報) | |||||
| タイトル | ||||||
| タイトル | Heat Partition in Wet Grinding of Fine Ceramics: Studies on Grinding of Hard-brittle Materials (2nd Report) | |||||
| 言語 | en | |||||
| 言語 | ||||||
| 言語 | jpn | |||||
| 資源タイプ | ||||||
| 資源タイプ識別子 | http://purl.org/coar/resource_type/c_6501 | |||||
| 資源タイプ | journal article | |||||
| 著者 |
細川, 晃
× 細川, 晃× 安井, 平司× 樋口, 浩司× 佐藤, 郁 |
|||||
| 書誌情報 |
精密工学会誌 = Journal of the Japan Society of Precision Engineering 巻 65, 号 6, p. 883-887, 発行日 1990-06-05 |
|||||
| ISSN | ||||||
| 収録物識別子タイプ | ISSN | |||||
| 収録物識別子 | 0912-0289 | |||||
| NCID | ||||||
| 収録物識別子タイプ | NCID | |||||
| 収録物識別子 | AN1003250X | |||||
| DOI | ||||||
| 関連タイプ | isIdenticalTo | |||||
| 識別子タイプ | DOI | |||||
| 関連識別子 | 10.2493/jjspe.65.883 | |||||
| 出版者 | ||||||
| 出版者 | 精密工学会 = The Japan Society for Precision Engineering | |||||
| 抄録 | ||||||
| 内容記述タイプ | Abstract | |||||
| 内容記述 | This report deals with the grinding heat partition into workpiece for two kinds of fine ceramics-normally sintered silicon carbide (SSC) and normally sintered silicon nitride (SSN)-in wet grinding. Based on a simple model of heat transfer in wet grinding in such that some portions of the total grinding energy (=q) is conducted into workpiece as heat (=qw) and part of qw flows into grinding fluid by convection (=qf) through the ground surface in the wheel-work interference zone, the heat partition into workpiece Rw is calculated. The heat partition of SSC is not affected so much by both table speed and wheel depth of cut with water-based grinding fluid. In the case of SSN, on the other hand, Rw increases from approximately 5% to 35% as table speed increases from 0.2 to 15 m/min. At lower table speed below approximately 1 m/min, however, the heat partitions are little influenced by table speed, in which the fragmented finished surface like SSC is dominant. The abrasive-workpiece interaction of SSN is affected by the grinding zone temperature, so that the surface morphology varies with grinding conditions as well as grinding heat partitions under the conventional grinding conditions. | |||||
| 権利 | ||||||
| 権利情報 | Copyright © The Japan Society for Precision Engineering 精密工学会 | |||||
| 著者版フラグ | ||||||
| 出版タイプ | VoR | |||||
| 出版タイプResource | http://purl.org/coar/version/c_970fb48d4fbd8a85 | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | http://www.jspe.or.jp/ | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | https://www.jstage.jst.go.jp/browse/jjspe | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | http://ci.nii.ac.jp/naid/110001368063/ | |||||
