WEKO3
インデックスリンク
アイテム
金属光造形複合加工金型を用いた射出成形サイクルタイムの短縮
https://doi.org/10.24517/00009668
https://doi.org/10.24517/00009668463ea838-a8c1-4625-8328-9c8cd2ac8cbf
| 名前 / ファイル | ライセンス | アクション |
|---|---|---|
TE-PR-YONEYAMA-T-662.pdf (1.2 MB)
|
.png)
|
| Item type | 学術雑誌論文 / Journal Article(1) | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 公開日 | 2017-10-03 | |||||||||||||||
| タイトル | ||||||||||||||||
| タイトル | 金属光造形複合加工金型を用いた射出成形サイクルタイムの短縮 | |||||||||||||||
| タイトル | ||||||||||||||||
| タイトル | Reduction in Injection Cycle Time Using a Milling-Combined Laser Metal Sintered Mold | |||||||||||||||
| 言語 | en | |||||||||||||||
| 言語 | ||||||||||||||||
| 言語 | jpn | |||||||||||||||
| 資源タイプ | ||||||||||||||||
| 資源タイプ識別子 | http://purl.org/coar/resource_type/c_6501 | |||||||||||||||
| 資源タイプ | journal article | |||||||||||||||
| ID登録 | ||||||||||||||||
| ID登録 | 10.24517/00009668 | |||||||||||||||
| ID登録タイプ | JaLC | |||||||||||||||
| 著者 |
米山, 猛
× 米山, 猛× 香川, 博之× 末廣, 栄覚× 阿部, 諭× 宮丸, 充 |
|||||||||||||||
| 著者別表示 |
Yoneyama, Takeshi
× Yoneyama, Takeshi
× Kagawa, Hiroyuki
× Suehiro, Yoshiaki
× Abe, Satoshi
× Miyamaru, Mitsuru
|
|||||||||||||||
| 書誌情報 |
成形加工 = Journal of the Japan Society of Polymer Processing 巻 19, 号 10, p. 662-668, 発行日 2007-10-20 |
|||||||||||||||
| ISSN | ||||||||||||||||
| 収録物識別子タイプ | ISSN | |||||||||||||||
| 収録物識別子 | 0915-4027 | |||||||||||||||
| NCID | ||||||||||||||||
| 収録物識別子タイプ | NCID | |||||||||||||||
| 収録物識別子 | AN10278882 | |||||||||||||||
| DOI | ||||||||||||||||
| 関連タイプ | isIdenticalTo | |||||||||||||||
| 識別子タイプ | DOI | |||||||||||||||
| 関連識別子 | 10.4325/seikeikakou.19.662 | |||||||||||||||
| 出版者 | ||||||||||||||||
| 出版者 | プラスチック成形加工学会 = Japan Society of Polymer Processing | |||||||||||||||
| 抄録 | ||||||||||||||||
| 内容記述タイプ | Abstract | |||||||||||||||
| 内容記述 | By composing a cooling channel just near the mold surface using the milling-combined laser metal sintering method, cooling during injection is promoted and the cooling time is reduced. In order to evaluate this effect, a cone with ribs inside the upper part is picked up. A spiral-cooling channel is fabricated along the side surface of the mold core and also between the ribs in the upper part. To compare with this, a steel mold with machined baffle channels was made. The diameter of the upper part of the molded cone was chosen as an evaluation dimension. The temperature on the upper surface of the core is kept low at around the cooling water temperature in the case of sintered mold during the cycle of the injection. On the other hand, the temperature on the upper surface of the steel mold increases far higher than the cooling water temperature. Cycle time for the same shrink ratio in the upper part of the molded cone was 25 s in the sintered mold and 40 s in the steel mold. Owing to the cooling time reduction, cycle time of the injection molding was reduced 35% by using the sintered mold with cooling channels. Simulation is available to evaluate the mold temperature distribution and is useful for improving the arrangement of cooling channels in the process of mold design. | |||||||||||||||
| 権利 | ||||||||||||||||
| 権利情報 | Copyright (c) 2009 社団法人 プラスチック成形加工学会 | |||||||||||||||
| 著者版フラグ | ||||||||||||||||
| 出版タイプ | VoR | |||||||||||||||
| 出版タイプResource | http://purl.org/coar/version/c_970fb48d4fbd8a85 | |||||||||||||||
| 関連URI | ||||||||||||||||
| 識別子タイプ | URI | |||||||||||||||
| 関連識別子 | http://www.jspp.or.jp/index.html | |||||||||||||||
| 関連URI | ||||||||||||||||
| 識別子タイプ | URI | |||||||||||||||
| 関連識別子 | http://ci.nii.ac.jp/naid/10023958625 | |||||||||||||||
| 関連URI | ||||||||||||||||
| 識別子タイプ | URI | |||||||||||||||
| 関連識別子 | https://japanlinkcenter.org/JST.JSTAGE/seikeikakou/19.662 | |||||||||||||||
