WEKO3
インデックスリンク
アイテム
非軸対称形状を有した刃先交換式ドリルの切削特性とMQLの適用効果
http://hdl.handle.net/2297/37028
http://hdl.handle.net/2297/370288f4d51f1-d089-4b10-9323-4b91d13b9e92
| 名前 / ファイル | ライセンス | アクション |
|---|---|---|
TE-PR-HOSOKAWA-A-4297.pdf (1.0 MB)
|
|
| Item type | 学術雑誌論文 / Journal Article(1) | |||||
|---|---|---|---|---|---|---|
| 公開日 | 2017-10-03 | |||||
| タイトル | ||||||
| タイトル | 非軸対称形状を有した刃先交換式ドリルの切削特性とMQLの適用効果 | |||||
| タイトル | ||||||
| タイトル | Cutting Characteristics of Indexable Insert Drill with Non-Axisymmetrical Geometry and Effects of MQL | |||||
| 言語 | en | |||||
| 言語 | ||||||
| 言語 | jpn | |||||
| 資源タイプ | ||||||
| 資源タイプ識別子 | http://purl.org/coar/resource_type/c_6501 | |||||
| 資源タイプ | journal article | |||||
| 著者 |
岡田, 将人
× 岡田, 将人× 上田, 隆司× 細川, 晃 |
|||||
| 書誌情報 |
日本機械学會論文集 C編 = Transactions of the Japan Society of Mechanical Engineers Series C 巻 77, 号 783, p. 4297-4307, 発行日 2011-01-01 |
|||||
| ISSN | ||||||
| 収録物識別子タイプ | ISSN | |||||
| 収録物識別子 | 0387-5024 | |||||
| NCID | ||||||
| 収録物識別子タイプ | NCID | |||||
| 収録物識別子 | AN00187463 | |||||
| DOI | ||||||
| 関連タイプ | isIdenticalTo | |||||
| 識別子タイプ | DOI | |||||
| 関連識別子 | 10.1299/kikaic.77.4297 | |||||
| 出版者 | ||||||
| 出版者 | The Japan Society of Mechanical Engineers = 日本機械学会 | |||||
| 抄録 | ||||||
| 内容記述タイプ | Abstract | |||||
| 内容記述 | The cutting performance of indexable insert drill that has non-axisymmetrical geometry is investigated. A solid drill that has axisymmetrical and twisted geometry is also used to compare the cutting characteristics. The diameter of drills is 16mm and carbon steel is used as work material. The application effects of MQL that oil mist is supplied from oil holes in the tool are also examined. The temperature of peripheral corner edge of outer insert is measured using a two-color pyrometer with an optical fiber. The tool temperature of indexable insert drill is higher than that of solid drill and it reaches approximately 525°C at highest. On the other hand, the thrust force of indexable insert drill is lower than that of solid drill and it do not change so much with cutting speed. The surface roughness of indexable insert drill is approximately 1.15-5.4μm and this is higher than that of solid drill in each cutting speed. However, it is improved by supplying the oil mist. | |||||
| 権利 | ||||||
| 権利情報 | Copyright © The Japan Society of Mechanical Engineers 日本機械学会 | |||||
| 著者版フラグ | ||||||
| 出版タイプ | VoR | |||||
| 出版タイプResource | http://purl.org/coar/version/c_970fb48d4fbd8a85 | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | https://www.jstage.jst.go.jp/browse/kikaic1979/-char/ja/ | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | http://www.jsme.or.jp/ | |||||
| 関連URI | ||||||
| 識別子タイプ | URI | |||||
| 関連識別子 | http://ci.nii.ac.jp/naid/130001433508 | |||||
