WEKO3
インデックスリンク
アイテム
研削仕上面あらさに及ぼす砥石減耗の影響
https://doi.org/10.24517/00011762
https://doi.org/10.24517/00011762a6f81009-0e42-466b-a91f-8b5f939044e0
| 名前 / ファイル | ライセンス | アクション |
|---|---|---|
AN00044309-8-1-93-103.pdf (316.4 kB)
|
.png)
|
| Item type | 紀要論文 / Departmental Bulletin Paper(1) | |||||
|---|---|---|---|---|---|---|
| 公開日 | 2017-10-03 | |||||
| タイトル | ||||||
| タイトル | 研削仕上面あらさに及ぼす砥石減耗の影響 | |||||
| タイトル | ||||||
| タイトル | Effct of Wheel Aear on Ground Surface Roughness | |||||
| 言語 | en | |||||
| 言語 | ||||||
| 言語 | jpn | |||||
| 資源タイプ | ||||||
| 資源タイプ識別子 | http://purl.org/coar/resource_type/c_6501 | |||||
| 資源タイプ | departmental bulletin paper | |||||
| ID登録 | ||||||
| ID登録 | 10.24517/00011762 | |||||
| ID登録タイプ | JaLC | |||||
| 著者 |
本多, 良辰
× 本多, 良辰× 進村, 武男× 高沢, 孝哉 |
|||||
| 著者別表示 |
Honda, Ryoshin
× Honda, Ryoshin× Shinmura, Takeo× Takazawa, Koya |
|||||
| 書誌情報 |
金沢大学工学部紀要 = Memoirs of the Faculty of Technology Kanazawa University 巻 8, 号 1, p. 93-103, 発行日 1974-03-25 |
|||||
| ISSN | ||||||
| 収録物識別子タイプ | ISSN | |||||
| 収録物識別子 | 0022-832X | |||||
| NCID | ||||||
| 収録物識別子タイプ | NCID | |||||
| 収録物識別子 | AN00044309 | |||||
| 出版者 | ||||||
| 出版者 | 金沢大学工学部 = Faculty of Technology Kanazawa University | |||||
| 抄録 | ||||||
| 内容記述タイプ | Abstract | |||||
| 内容記述 | In this paper, changes in the surface roughness of a workpiece, that probably happen due to the wheel wear during the grinding process, are analytically dug out by comparing with some experimental results. From the continuous observation of the wheel and the work surface it is found that the ground surface becomes coarser with the wheel wear, and at the same time that the distribution of the grain cutting edges on the wheel changes. A formula of the ground surface roughness is derived from the analysis of the grinding mechanism on the assumption that each cutting edge is shaped in conical frustum, as verified in the above observation, herewith the actual variations in the width of the wear land on the cutting edge and in the distribution of the cutting edges during the grinding process being taken into consideration. As a final consequence it is confirmed that the typical tendency of the roughness calculated from the formula closely agrees with the experiment. The extent of roughness of the work surface seems to be restrained by the dulling of the cutting edges. |
|||||
| 著者版フラグ | ||||||
| 出版タイプ | VoR | |||||
| 出版タイプResource | http://purl.org/coar/version/c_970fb48d4fbd8a85 | |||||
